Structural Fire Damage Cleaning in Perry, FL
The drywall is gone, and now you are staring at blackened studs, scorched joists and a charred roof deck. Somebody now has to decide what gets blasted clean, what gets sistered and what gets replaced. Unify Fire Solutions puts you in touch with independent, licensed and insured Perry contractors who clean the bare structure down to sound wood.
- Soda, dry ice and hand cleaning of framing
- Char depth probed member by member
- Cleaned wood encapsulated against lingering odor
What Makes Framing Work Different
Close up the walls over dirty framing and the smoke odor bleeds right back through the new finish. This stage decides whether your rebuilt rooms smell fresh or smell burned for years.
Licensed & Insured Independent Pros
Each contractor on our referral list is an independent, licensed and insured local company. Verify both, and ask whether the crew follows the IICRC S700 standard for fire and smoke work.
Upfront Written Estimates
Media blasting depends on square footage, the media used and how hard the space is to get into. Ask for a line-item written estimate before the first bag of media is opened.
Rapid Local Dispatch
Day or night, a dispatcher picks up and starts looking for a structural cleaning crew right away. Timing depends on which crews near Perry are free, and it is often the same day.
Blasting Rigs and Probing Tools
Structural crews bring soda blast pots, dry ice units, big compressors, HEPA vacs, air scrubbers and a sharp awl to test every member.
Do not climb into a burned attic or walk a scorched roof deck to look for yourself. Burned joists and decking can fail under one person's weight, and open wiring may still carry current. Wait for the contractor to check that the structure is safe, and keep people off floors that sit over a burned crawlspace or basement.
Cleaning the Building From the Roof Deck Down
Furniture and debris are a separate job. This page is about the framing, masonry and steel that actually carry the load.
Char Depth Probing and Member Decisions
An awl pushed into a charred stud tells the story: if it stops in sound wood after a thin layer of char, the member is usually a cleaning candidate. When the char cuts deep into a joist or a truss web, the member gets sistered or swapped out.
- Members marked clean, sister or replace
- Structural engineer called in for questionable beams, trusses and headers
- Photos of each marked member for the claim
Soda Blasting
Baking soda media knocks soot and surface char off framing while leaving the grain mostly intact. It leaves a fine white dust and some residue, so containment and a thorough HEPA vacuum afterward are part of the job.
Dry Ice Blasting
With dry ice the pellets sublimate on impact, so there is nothing left on the floor but the soot itself. It works well in tight attics and around wiring, though it costs more and is noisy.
- Hearing protection and ventilation required
- Good choice when residue would be a problem
Wire Brushing and Sanding
For a few blackened studs or a small closet fire, wire brushes, sanding discs and a HEPA-shrouded grinder may be all it takes. It is slow on big areas but precise where blasting would be overkill.
Brick, Block, Concrete and Steel Beams
Porous brick, block and concrete trap soot deep in the surface, so crews use alkaline detergents, scrub brushes or blast media to lift it. Steel beams get cleaned and inspected for any heat warping, with doubts sent to the engineer.
Encapsulation and Attic Insulation Removal
Cleaned framing gets a coat of shellac-based or specialty encapsulant to lock in any odor left deep in the wood. Attic jobs start by vacuuming out the smoky blown-in or batt insulation so the rafters and roof deck can be reached.
Crawlspaces get the same treatment on a smaller, dirtier scale: floor joists, sill plates and the underside of the subfloor are probed, blasted where needed and sealed. A smoke-stained or wet vapor barrier usually comes out and goes back new.
Have the contractor explain the method they plan for each part of the house. It is common to see soda in open walls, dry ice in the attic and hand sanding near the electrical panel on the same job.
Plan for containment, because blasting throws soot and media into every corner it can reach. Expect poly over openings, taped-off HVAC returns and air scrubbers pulling the space under negative pressure during blasting. Ask what the plan is to shield the undamaged rooms, floors and glass.
Looking at Blackened Studs and Rafters?
Phone our dispatchers and they begin searching for a structural crew close to Perry. It costs nothing to call.
Call +1-833-336-1630How a Structural Cleaning Job Unfolds
- 1
Phone the Dispatcher
Say which parts of the structure are open now, such as walls, attic, crawlspace, masonry or steel. Mention if a roofer, engineer or adjuster has already been out.
- 2
Mobile Crew on Site
An independent crew shows up with its compressor, blast gear, poly and air scrubbers. First they confirm the roof deck and floors will hold weight and that the exposed circuits are dead.
- 3
Probe, Mark and Quote
Every exposed member gets probed with an awl and marked clean, sister or replace, and anything borderline goes to a structural engineer. You get a written, line-item quote listing square footage, method, sealer and insulation removal before any work starts.
- 4
Blasting, Sealing and Walkthrough
Once the wood is blasted, vacuumed and sealed, the crew lead walks you through the open structure. Smell the space on a warm day and get photos of each tagged member before anyone hangs drywall.
Notes From People We Connected
After the attic fire, the rafters were black and the blown-in insulation was a wet mess. They vacuumed out the insulation, dry iced the rafters around the wiring and sealed it all. Two rafters were cut deep enough that they called in an engineer, and those got sistered.
I assumed every black stud in the hallway had to be replaced. The crew lead probed each one with an awl and showed me that most were just surface char. They soda blasted and sealed them, and only three were swapped.
The fire in our lower level left the block walls and the steel beam coated in soot. The contractor cleaned the block and the beam, then had an engineer check the steel for warping. The basement smells normal again, even closed up.
Your Structural Fire Cleaning Questions Answered
How do crews decide if a charred stud can stay?
The test is simple: they probe it. Push an awl into the char, and if it hits solid wood after a shallow layer, the stud is usually a cleaning job. Members with deep char, splitting or a lost cross section get sistered or replaced, and anything structural in doubt goes to a licensed structural engineer.
What is the difference between soda blasting and dry ice blasting?
Soda blasting uses sodium bicarbonate media that is gentle on wood and helps neutralize odor, but it leaves dust and residue to clean up. Dry ice leaves no media behind and works well near wiring, but the equipment is noisy and the job usually costs more. It is common to see both on one job.
Why seal the framing if it has already been cleaned?
Smoke gets deep into the pores of the wood, past what blast media can reach. A shellac-based or specialty encapsulant locks that residual odor in so it cannot off-gas through the new drywall. Sealer only works over clean framing, never as a shortcut over soot.
Does the attic insulation have to come out after a fire?
In most cases where smoke got into the attic, it does. Loose-fill and batts act like a giant filter for smoke, and hose water often soaks them as well. It is vacuumed out with an insulation vac so the rafters and roof deck can be probed, blasted and sealed before anything new is blown in.
Can soot be cleaned off brick and concrete block?
Usually yes, though masonry takes more effort than drywall because soot sinks into the pores. Crews use alkaline masonry cleaners and stiff brushes, and soda or other media blasting for heavy buildup. Heat-cracked or spalled block and brick should be looked at by an engineer or mason.
Do I need a structural engineer for fire-damaged framing?
Not for every job, but for anything load-bearing that looks questionable, yes. Trusses, beams, headers, steel and heavily charred joists are where an engineer's letter protects you and helps the claim. Your local building department may also require one before the walls close.
Charred Framing Cleaning Across Perry and Beyond
Our dispatch line covers Perry and the nearby communities around it, from older homes with plaster and solid-sawn joists to newer builds with engineered trusses. Attics, crawlspaces, basements, garages and small commercial buildings are all in scope.
- Attic fires
- Electrical fires
- Furnace puff-backs
- Chimney fires
- Lightning strikes
- Neighbor's fire spread
Should the first contractor not suit you, ring us again and we will connect you with a different one. Do not let the rebuild close walls over dirty framing.
